Wave transport in 1D stealthy hyperuniform phononic materials made of non-resonant and resonant scatterers

Stealthy hyperuniform point patterns are characterized by a vanishing spatial Fourier transform around the origin of the reciprocal vector space. The long-range point density fluctuations are suppressed as well in materials consisting of such distribution of scatterers, opening up opportunities to control waves. Beside wave transport in such structured materials are driven by several elements, such as the acoustic properties of the host material, the scatterer characteristics, i.e., dimensions or resonant features, and the scatterer distribution patterns. The effects of these three basic elements on the wave transport properties are usually hard to discriminate. In this work, we analyze the transport properties of acoustic waves in one-dimensional phononic materials constituted of either non-resonant or resonant scatterers distributed along stealthy hyperuniform patterns in air. The pattern is controlled by the stealthiness, allowing us to continuously vary from random phononic materials to phononic crystals. The properties of the scatterers are controlled by their size and/or the resonant frequencies. The properties of the host material are controlled by the viscothermal losses. Transport properties of stealthy hyperuniform materials are found to be robust to both the scatterer dimensions and inherent viscothermal losses, while strongly affected by the scatterer resonances, which introduce sharp dips in the transmission coefficient.


I. INTRODUCTION
In recent years, the wave physics community has become increasingly interested in stealthy hyperuniform materials, as the dispersion relations of these materials exhibit isotropic bandgaps although they are not periodic. [1][2][3][4][5][6][7][8][9][10][11][12][13] These isotropic bandgaps have been exploited to design isotropic filters and free-shaped waveguides with both photonic 8,9 and phononic 6 hyperuniform materials. Stealthy hyperuniform materials are structured materials whose scatterer distribution induces the complete suppression of incident wave scattering for a set of wave vectors in the low frequency limit in the Born approximation. 14 In this sense, periodic structures like photonic 15 or phononic 16 crystals form a subset of stealthy hyperuniform materials. Waves propagating in a periodic medium are either diffracted by Bragg scattering or transmitted, thus introducing either Bragg peaks or zero regions in the structure factor. 17,18 Nevertheless, hyperuniformity further enhances the suppression of long-range point density fluctuations, 11 thus introducing correlated disorder to control waves. Waves propagating in these materials with correlated disorder present a phase diagram with transparent regions, Anderson localization, bandgaps, and wave diffusion. 5 Transport properties in one-dimensional (1D), 19 quasione-dimensional, 20 and higher dimensional systems have been controlled by correlated disorder, allowing the design of efficient non-resonant absorbers made of dilute disordered materials for broadband and omnidirectional waves. 21 Systems based on correlated disorder with target combination of transparent and nontransparent frequency regions for both electromagnetic 22 and ARTICLE scitation.org/journal/apm acoustic 23,24 waves have also been designed. The properties of stealthy materials appear to be robust to the losses present under realistic conditions, demonstrating the potential of correlated disorder for practical designs.
Wave transport in such materials is driven by several elements, such as the scatterer distribution patterns, the scatterer characteristics, i.e., dimensions or resonant features, and the acoustic properties of the host material. The effects of these three basic elements on the material transport properties are usually hard to discriminate. On the one hand, the concept of the stealthy hyperuniformity introduces an elegant way to design point patterns with finely tunable correlations encoded by the degree of stealthiness χ. [1][2][3][4][5]8,9,[11][12][13] Asymptotic values of χ correspond to Poisson distribution, χ → 0, and perfect crystal lattices, χ → 1. More precisely, three structural regimes are distinguished 25,26 when χ increases: disordered, wavycrystalline, and crystalline regimes. 26 Therefore, a continuous variation of χ from 0 to 1 induces a continuous change from the random point patterns to the periodic ones. On the other hand, the scatterers used for the design of stealthy hyperuniform materials in photonic 2,8,9 and phononic 6 systems are Mie resonators, the resonance of which is fixed close to the Bragg frequency by optimizing its dimensions for a given material. Recently, the effect of the local resonances in stealthy hyperuniform acoustic materials has been preliminary analyzed, showing a strong effect on the wave transport properties in the transparency band. 10 Moreover, in elastodynamics, the exact expressions for the effective properties of two-phase composites in the long-wavelength (quasistatic) regime via homogenized constitutive relations that are local in space have been applied to stealthy hyperuniform materials. 27 These local approximations have been extended beyond the quasistatic regime by postulating nonlocal formulas based on the similarities between electrodynamic and elastodynamic problems and the rigorous formulation of the nonlocal effective dynamic dielectric properties. By using these nonlocal microstructure-dependent approximations, it is shown that stealthy hyperuniform materials are less lossy than their nonhyperuniform counterparts in the quasistatic regime, and stealthy hyperuniform media can be perfectly transparent for a wide range of wavenumbers. 27,28 Finally, the presence of losses that cannot be avoidable in some types of waves, like the acoustic waves, is only accounted for in few works. 23 In this work, we consider 1D phononic materials that allow us to easily discriminate such kinds of elements. Therefore, we discuss the fundamental effect of each element on the opening of bandgaps in stealthy hyperuniform materials. This allows us, for example, to place the resonance in different locations of the frequency spectrum even also outside of the transparency range and to analyze the possibly coupling with Bragg interferences, for instance. The point patterns are created by an optimization algorithm that minimizes the structure factor, 23,24 related to the scattering properties of the corresponding systems in the weak scattering approximation. 17,18 The wave transport properties are first analyzed in these 1D phononic structures going from disordered materials to ordered ones (phononic crystals) when χ varies continuously. We then compare these properties to those of the same 1D phononic materials when either non-resonant or resonant scatterers are located at the positions of the point patterns. We thus discuss the impact of the individual scattering properties of the scatterers constituting the whole material. We point out that the viscothermal losses, unavoidable in acoustics, are also accounted for. In practice, we use an air-filled square cross-sectional waveguide in which the stealthy hyperuniform materials made of non-resonant and resonant scatterers are embedded. A non-resonant scatterer consists of a local narrowing of the waveguide cross section such that it has a nonresonant behavior in the analyzed range of frequencies. A resonant scatterer consists of the same non-resonant scatterer but additionally loaded by a quarter-wavelength resonator.

II. STEALTHY HYPERUNIFORM POINT PATTERNS
A. Structure factor Let us consider a distribution of N points placed at positions ⃗ ri (i = 1, . . . , N) inside a domain Λ in d-dimensions. The structure factor, S(⃗ q), of this point pattern is defined as its spatial Fourier transform and reads as follows: where ⃗ q is a vector in the Fourier or reciprocal space. The hyperuniformity concept can be defined by either the local number variance σ 2 (R) (i.e., the variance in the number of points within a randomly thrown spherical window of radius R) of the point pattern in the real space or the structure factor S(⃗ q) in the reciprocal or Fourier space. In this work, we use the structure factor S(⃗ q). Hyperuniform point patterns present a structure factor vanishing in the long-wavelength limit, i.e., S(q → 0) = 0, where q = |⃗ q|. One can define the stealthy hyperuniform point patterns as those presenting a structure factor that vanishes around the origin, S(Ω) = 0 with Ω the set of q ∈ [0, q c ].
To design the stealthy hyperuniform pattern, we use an optimization procedure, which looks for the positions ⃗ ri that minimizes the structure factor for a target region q < q c as described in Refs. 23 and 24. The algorithm provides a certain configuration starting from a random distribution. We can introduce a constraint as minimal distance l between scatterers by the following expression: | ⃗ ri − ⃗ rj| ≥ l ∀i ≠ j. This can be used as a posteriori to build realistic materials with finite size scatterers and thus to analyze the wave transport properties in realistic conditions. The objective functions to be simultaneously minimized are a summation of the structure factor and the standard deviation function We note that the distribution of points obtained by this optimization procedure is equivalent to those obtained by the collectivecoordinate optimization technique described in Refs. 12, 14, 25, and 26 when l = 0.

B. Stealthiness
In this section, we define the stealthiness, χ, which characterizes the point pattern that meets the hyperuniformity definition. The

ARTICLE
scitation.org/journal/apm stealthiness is the ratio of the number M(Ω) of the constrained vectors in Ω to the number of degrees of freedom in the real space d(N − 1) in d-dimensions (if the system translational degrees of freedom are removed). We consider a 1D domain of length L and Ω becomes a segment of length q c . Therefore, M(Ω) = (q c L/2π), and for N ≫ 1, Note also that the expression of χ for higher dimensions is strongly dependent on the shape of the domain Ω. 7,13 Let us define here the set C(χ) that will stand for the set of configurations ⃗ ri with i = 1, . . . , N that satisfies S(q < 2πNχ/L) = 0. It is clear that C(χ = 0) includes all the point pattern configurations and that C( In this section, we analyze the structure factor of different stealthy hyperuniform point patterns generated with different values of χ. The minimum distance between points is fixed at l = L/100, i.e., | ⃗ ri − ⃗ rj| ≥ L/100 ∀i ≠ j. Thus, the generated point patterns will allow the use of finite width scatterers in a second step. We consider N = 25 points as an example. Figure 1(a) shows the map of the log(S(⃗ q)) in terms of χ and qL/2πN. The red continuous line delimits the constrained frequency region imposed by the value of χ. As demonstrated in Ref. 25, three regions are identified We note here that the behavior for higher dimensions is similar with three regions named as "disordered", "wavy-crystalline," and "crystalline." 26 For clarity, we start by analyzing the lower and upper regions corresponding to the two bounds of χ.
In region (i), 0 ≤ χ ≲ 1/3, the structure factor behavior is twofold: For q ≤ q c , the values of the structure factor are orders of magnitude smaller than those for q > q c . As an example of typical behavior, both the point pattern and the structure factor calculated for χ = 0.2, as indicated by the horizontal dashed black line in Fig. 1(a), are depicted in Fig. 1(b). The point patterns in this region are disordered and the optimization problem is highly degenerated due to the high dimension of the set C(χ).
In region (iii), 1/2 ≤ χ < 1, the unique solution of the minimization problem is the periodic pattern. 25 The local dimension of C(χ) is 1, corresponding to the periodic point distribution. The structure factor map depicted in Fig. 1(a) presents the Bragg peaks 17,18 at q B = n2πN/L, with n ∈ Z. The point pattern crystalizes in a 1D array whose periodicity is a = L/N. In this case, ⃗ qB represents the well-known vectors of the reciprocal lattice in the reciprocal space of the periodic system.
In region (ii), 1/3 ≲ χ < 1/2, the point pattern undergoes a transition from disordered to a periodic pattern and combines the properties of the other two regions. The structure factor smoothly mixes the behavior of region (i), in which it is minimized only for q < q c , and that of region (iii), in which it is minimized for all q different than those corresponding to Bragg peaks. Therefore, the structure factor alternates between minimal and non-minimal

ARTICLE
scitation.org/journal/apm values. To illustrate this dynamic, the point distribution and the structure factor for χ = 0.39 and χ = 0.47, as indicated by the two horizontal dashed black lines in Fig. 1(a), are represented in Figs. 1(c) and 1(d). For the case χ = 0.39, S(⃗ q) is minimum in the region q < q c , but other minima appear. For χ = 0.47, which is a value very close to the limit of this region, S(⃗ q) presents in addition smooth alternation of minima and maxima for q > q c . The structure factor for stealthy hyperuniform point patterns in the absence of constraint on l is analyzed in the supplementary material. Its overall behavior is preserved. The three χ-dependent regions appear at the same limits. However, it should be noticed here that the minima of S(q) are much clearer than in the constrained case presented in this section.

III. WAVE TRANSPORT PROPERTIES IN STEALTHY HYPERUNIFORM PHONONIC MATERIALS
Wave transport is calculated by using the transfer matrix method as explained in the supplementary material. With the 1D stealthy hyperuniform acoustic material being an asymmetric and reciprocal structure, it is successively excited by a plane wave from one side and then from the other side in order to evaluate the scattering coefficients, i.e., the two reflection coefficients, R + and R − , and the transmission coefficient T. The eigenvalues of the transfer matrix provide the dispersion relation of the material, the supercell of which is composed of N scatterers arranged on the stealthy hyperuniform pattern. Problems are solved with and without viscothermal losses. Losses are accounted for via effective complex and frequency dependent density and bulk modulus as given in Ref. 29.

A. 1D stealthy hyperuniform acoustic materials
We consider a 1D stealthy acoustic material consisting of an air-filled waveguide of square cross section presenting N = 25 scatterers. These scatterers are either non-resonant, made of identical rectangular cross section scatterers (reduction of the main waveguide section along a single direction), or resonant, made of these rectangular cross section scatterers additionally loaded by identical quarter-wavelength resonators (see Fig. 2 for details). The waveguide side W is chosen such that only plane waves propagate, i.e., the frequencies are lower than the first cutoff frequency of the waveguide. The rectangular cross section scatterer consists in a reduction of the waveguide cross section along a single direction of thickness l d ≡ l; therefore, the rectangular cross section scatterer presents a width W and height h d = ζ d × W, where ζ d ≤ 1 is the height (section) reduction ratio. The quarter-wavelength resonator consists in a cylindrical tube of radius Rq = l d /4 and length lq. Its resonance frequency is fs ≃ cq/4lq, where cq is the sound speed of the fluid in the cylindrical tube. The scatterers are arranged on the stealthy hyperuniform pattern, ⃗ ri ≡ xi in the 1D domain Λ, analyzed previously (constraint l = L/100). The length of the 1D domain is L = 1 m and the side is W = 1.5 cm. The scatterer thickness is fixed at l d = L/100 = 1 cm, thus fixing the radius of the quarter-wavelength Rq = 2.5 mm. The scattering intensity of the non-resonant scatterers is varied by modifying the section reduction ratio ζ d = [0.33, 0.5, 0.66, and 0.83]. The  Fig. 3(a)], the scattering is weak and the transmission coefficient is mainly affected by the Bragg interferences when χ > 0.45. The three χ-dependent regions described in Sec. II C are weakly visible.
The scattering intensity increases together with the impedance mismatch between the rectangular cross section scatterer and the main tube, i.e., with the decrease of ζ d . The transmission coefficient is thus more impacted by the pattern, as can be seen in Figs. 3(b)-3(d). The bandgap width of the periodic distributions (χ ≥ 0.5) decreases with the ratio ζ d . The transparency regions for f < fc are clearly visible in Figs. 3(b)-3(d). This transparency zone is one of the main characteristics of the stealthy hyperuniform materials and is a direct translation of the constraints imposed on the structure factor. We can clearly see how the spatial distribution of the scatterers impacts the transmission coefficient in each of the three regions: for χ ≲ 1/3, where the point pattern is mostly disordered without any hint of periodicity, we see the transparency for f ≤ fc and the low transmission coefficient region for f > fc; for χ ≥ 1/2, we can see that only the region around the Bragg frequency is impacted by the scattering; for 1/3 ≲ χ < 1/2, the characteristic transition zone with the alternating transparent and nontransparent zones as imposed by the structure factor is shown.
Both the scattering properties and the dispersion relation  Fig. 3(d)]. First, these properties are analyzed in the absence of losses. In that case, R + ≠ R − because the structure is asymmetric, but |R + | = |R − | because of energy conservation. The cutoff frequency fc imposed by χ is shown by the vertical thick dashed black lines in Figs. 4(a)-4(c). The scattering coefficient behavior is clearly different if f is lower or larger than fc. When f ≤ fc, the characteristic Fabry-Pérot peaks are visible in the scattering parameters. They are due to the finite size L of the sample, the effective impedance of which is different from that of the surrounding medium. When f > fc, no Fabry-Pérot peaks are noticed. In particular, the alternation of transparent and non-transparent regions translates the transition between the disordered and periodic distribution of scatterers when χ ≃ 0.5 [see Fig. 4(c)]. Figures 4(d)-4(f) show the complex dispersion relation calculated for χ = [0.2, 0.39, and 0.47] considering the system with N = 25 as a supercell with periodicity L (see the supplementary material for more details). A different behavior is again observed depending on whether f is lower or higher than fc. When f ≤ fc, the system presents, for all the analyzed cases, a dispersion relation with near zero imaginary part of k and a linear dispersion relation for the real part. When f > fc and χ ≲ 1/3 [ Fig. 4(d)], the real part of the dispersion relation is characterized by flat bands. These modes are mostly localized in the structure due to the disordered feature of the system. When 1/3 ≲ χ < 1/2 [see Fig. 4(e)], regions with flat bands alternate with dispersive bands in the real part, which correspond to the alternation of the transparent and opaque frequency regions in the transmission coefficient. We note that the system becomes dispersive close to fc when χ > 0.5 (due to the periodicity imposed by the crystallization). That is the reason why the calculated limit fc [vertical thick dashed black line in Fig. 4(f)] considering c the speed of sound in air fits with neither the frequency at which the dispersion relation starts to present an imaginary part [see Fig. 4(f)] nor the beginning of the opaque region in scattering coefficients in Fig. 4(c).
The effect of viscothermal losses in the system is now analyzed. Thick black continuous lines in Fig. 4 show both the transmission coefficient |T| and the imaginary part of the dispersion relation calculated considering the complex and frequency dependent density and bulk modulus in each part of the waveguide. The transparency region when f ≤ fc is impacted by the viscothermal losses but as shown by the dispersion relation is robust to losses. We note that the decrease of |T| is very close to that in an empty waveguide as shown in Ref. 23. When f > fc, the peaks of the transmission coefficient, due to the low dispersion bands of the dispersion relation, are strongly affected and the amplitude is reduced. In this case, we note that due to the viscothermal losses |R + | ≠ |R − | although the results are not shown in the figure for simplicity.

C. Resonant scatterers
In this section, we introduce both the resonance effect and the viscothermal losses into the system. We analyze its  In order to compare, we refer to the non-resonant case shown in Fig. 3(d). If we now reduce the value of the stealthiness, the region of low transmission coefficient strongly increases in frequency as shown in Figs. 5(b) and 5(c): the high frequency transmission range shown in the periodic case is suppressed as periodicity is removed. For example, for χ = 0.2, the bandgap starts at fL/cN = 0.35, showing a broad range of frequencies with very low values of transmission coefficient for higher frequencies of the analyzed range. For all the cases, we notice that the transparency region imposed by χ is preserved.

IV. CONCLUSION
The wave transport properties of 1D phononic materials made of stealthy hyperuniform distributions of non-resonant or resonant scatterers are analyzed in this work. The stealthiness is used to continuously analyze the properties from random distribution to periodic ones. In the reciprocal space, there are three regimes characterizing the point patterns. The disordered region, (i) 0 ≤ χ ≲ 1/3, is characterized by transparent and opaque frequency regions with the cutoff frequency imposed by χ. The wavy-crystalline region, (ii)1/3 ≲ χ < 1/2, is characterized by both the transparent frequency range imposed by χ and an alternation of opaque and transparent frequency regions depending on the value of χ. We note that in this region, the point pattern shows a dimerization made of two sublattices with periodicity 2L/N when χ approaches to 0.5. The last region is the crystalline, (iii)1/2 ≤ χ < 1, in which the Bragg peaks are clearly visible and the point distribution is purely periodic. Once the point pattern is built and analyzed, the phononic material is made by adding non-resonant and resonant scatterers at these positions. The material is made by an air-filled waveguide in which the cross section is adapted to be always in the plane wave regime. The investigations for the non-resonant scatterers show that the behavior of the structure factor is well-captured by the scattering coefficients of the system. However to clearly identify the three regions, a given impedance mismatch is necessary. Interestingly, the lossless system exhibits purely real dispersion relation in the transparent region imposed by χ. The wave transport properties are shown to be robust to the presence of viscothermal losses. The response of the system made of resonant scatterers is richer due to the fact that the resonance of the individual scatterers, fs, is added to the system and can be exploited to couple with the scattering effects provided by the point pattern. When fs ≃ fB, while the effect of superbandgap is observed for periodic structures χ ≥ 1/2, for χ < 1/2, a broader deep of the transmission coefficient appears from fs. Moreover, when fs ≃ fc, wide deeps of the transmission coefficient are also created. If the resonance is placed away of fc or fB, the resonance and the scattering due to the point pattern can be combined independently to produce frequency ranges with low amplitude of the transmission coefficient. In particular, the disordered systems with resonant scatterers present better performances to be used as acoustic isolation systems than the periodic ones when losses are considered.

SUPPLEMENTARY MATERIAL
See the supplementary material for the detailed description of the transfer matrix method used to analyze the stealthy hyperuniform materials described in this work. The analysis of the structure factor for stealthy hyperuniform materials generated without constraints, i.e., with l = 0, is also shown.