Physics and applications of three-ion ICRF scenarios for fusion research

JET Contributors,,


I. INTRODUCTION
Strong magnetic fields are used to confine plasmas in fusion devices. As a result of the Lorentz force, plasma ions and electrons gyrate around the magnetic field lines with a local characteristic cyclotron frequency x cs ¼ q s B/m s , where q s and m s are the charge and the mass of the particle and B is the local value of the magnetic field. Note that ions rotate in the clockwise direction, while electrons rotate counterclockwise, when viewed in the direction opposite to the magnetic field. For typical magnetic fields in present-day and future tokamaks, the ion cyclotron frequencies broadly cover the range between $10 MHz and $100 MHz. A system for plasma heating with waves in the ion cyclotron range of frequencies (ICRF) is under development for ITER, aiming to deliver 20 MW of heating power in the frequency range 40-55 MHz. [1][2][3][4] In addition to plasma heating, ICRF systems have a broad range of additional applications, as discussed in recent overviews. 5,6 ICRF heating relies on the excitation of fast magnetosonic waves that can be absorbed by both ions and electrons via a large number of collisionless absorption mechanisms in the plasma. 7-10 A necessary condition for fundamental ion cyclotron (n ¼ 1) and harmonic damping (n ¼ 2, 3, …) is the local match between the Doppler-shifted wave frequency and the ion cyclotron frequency or harmonics Here, x ¼ 2pf with f being the frequency of the launched radio frequency (RF) waves; k jj and v jj,i are the wavenumber and ion velocity parallel to the confining magnetic field; and n is the cyclotron harmonic number. In turn, Eq. (1) determines the parallel velocities for resonant ions v jj;i ¼ x À nx ci ð Þ =k jj : For thermal ions with low v jj , this condition can be fulfilled close to the ion cyclotron resonance layers, where x % nx ci . Note that the physics of ICRF heating is very rich and extends beyond ion cyclotron interactions only. In particular, fast waves can also be absorbed directly by electrons or undergo a transformation to shorter wavelength modes via mode conversion. 11,12 The RF electric field of the propagating fast waves can be written as the sum of a left-hand, E þ (rotating in the direction of the ions) and a right-hand, E À (rotating in the direction of the electrons) polarized component. 13 Efficient ion cyclotron damping for thermal and moderately energetic ions occurs when Eq. (1) is satisfied in a region with a high jE þ j. 9 To a large extent, the plasma composition determines the spatial distribution of the ratio E þ /E À in the plasma volume and thus is a crucial parameter to optimize the ICRF heating efficiency.
Out of all existing ICRF heating scenarios, minority heating is the most routinely used in fusion research. In its simplest version, this heating scenario is realized in two-ion species plasmas with different charge-to-mass ratios, where the concentration of one of the ion species (minority) is much lower than that of the other one. Minority ions absorb RF power close to their cyclotron resonance, x % x ci,mino (n ¼ 1). In its purest form, minority heating is obtained at a negligible minority concentration that is low enough such that it does not affect the wave propagation characteristics. 7,8 In practice, minority heating is applied at higher minority concentrations, X mino ¼ n mino /n e (here, n mino is the minority density and n e is the electron density), typically from a few % to $10%. This is not only due to a higher density of resonant ions, but also because of the appearance of the so-called ion-ion hybrid (IIH) layer. 14 The E þ component is locally enhanced at this layer (see Sec. II), facilitating RF power absorption by minority ions.
The radial position of the IIH layer in the plasma depends on the plasma composition. 12 As the concentration of minority ions increases, the IIH layer shifts further away from the minority cyclotron resonance toward the cyclotron resonance of the other ion species. Eventually, the distance to the IIH layer gets too large for both plasma ion species and they can no longer resonate at the region with an enhanced jE þ j. Under these conditions, ICRF heating via mode conversion becomes dominant, where launched RF fast waves undergo a transformation into shorter wavelength modes, mostly used (but not only) for local electron heating and plasma flow generation. 11,12,15,16 However, there is an elegant solution to transform mode conversion electron heating back into ion cyclotron heating under these conditions. This can be achieved by adding a new degree of freedom to the system and extending the plasma composition beyond two thermal ion species by providing an additional ("third") ion population. [17][18][19][20] Obviously, a proper choice for the plasma composition is required such that the third resonant ion population satisfies the wave-particle interaction condition, Eq. (1) in the vicinity of a layer with a large jE þ j in such multi-ion species plasmas. In fact, as demonstrated in Sec. II, there are two equivalent possibilities for the choice of the third resonant ion population: (a) an ion population with an intermediate charge-to-mass ratio 17,18 and (b) a fast-ion population with sufficiently large parallel velocities such that they resonate at the IIH layer because of their large Doppler shift. 19,20 In the latter case, the charge-to-mass ratio of the resonant absorbers can be the same as for one of the main plasma ions. Thus, in its simplest form, such an ion cyclotron heating scenario can be realized in a plasma composed of at least two ion populations with different charge-to-mass ratios and another population with either a third charge-to-mass ratio or a significantly different parallel velocity; hence, it is called the three-ion ICRF scenario.
In hindsight, this sounds like a trivial idea. In fact, as illustrated in this paper, three-ion scenarios were already effectively at work in D-T, D- 3 He, and H-D plasmas on TFTR, JET, and ASDEX Upgrade (AUG) (see Sec. IV and references therein). Remarkably, while all the essential elements were recognized by the authors, including the effect of intrinsic and extrinsic impurities on the spatial distribution of jE þ j and ICRF characteristics, 15,21 the flexibility and tunability of these RF scenarios was apparently not realized as such. These scenarios rely on an active control of the jE þ j RF electric field in the plasma by selecting the plasma mix such that the third ion population resonates in the vicinity of one of the IIH layers. The intentional use of three-ion ICRF scenarios only started a few years ago and highlighted their strong potential and wide range of applications for fusion research beyond plasma heating (see Secs. II, III, and V).
The simplicity of the name should not confuse the reader: nothing prevents applying this ICRF scenario in plasmas with more than three ion populations. In fact, the name of this novel ICRF scenario provides an umbrella for a large variety of options possible in multiion species plasmas to transform mode conversion electron heating into a flexible ion cyclotron heating scenario. Note that three-ion ICRF scenarios rely on the fundamental (n ¼ 1) ion cyclotron damping. As for any other n ¼ 1 ICRF scenario, the achieved fast-ion energies can be controlled by a number of actuators, including absorbed RF power per resonant ion, plasma density, electron temperature, etc. 13 This, in turn, allows to control whether collisional electron or bulk ion heating dominates as a result of the slowing-down of the resonant ions.
For a given plasma density, electron heating can be maximized by reducing the number of resonant absorbers and depositing the RF power in the central regions of the plasma. On the other hand, selecting heavier ions and moderating fast-ion energies is beneficial for maximizing collisional bulk ion heating. All this is a consequence of the physics of Coulomb collisions in a plasma, but realizing efficient RF power absorption by heavy ions is not that straightforward. Three-ion ICRF scenarios are particularly suited for this task, as they allow one to channel RF power to, e.g., 9 Be impurities in D-T plasmas, with promising applications for ITER and JET with the ITER-like wall (JET-ILW The examples presented in this paper show that for almost any plasma mix of interest, a suitable three-ion ICRF scenario can be designed for a specific application. The experimental studies carried out so far have shown that these scenarios allow one to probe important aspects of future high-power D-T plasmas. As discussed in the following chapters, the success of the experiments with three-ion ICRF scenarios on the tokamaks Alcator C-Mod, JET, and AUG provided further insights into the plasma effects associated with the presence of MeV-range ions, a field of study that will become more and more important in the near future in fusion research. Applications of three-ion ICRF scenarios are not only limited to laboratory magnetic confinement plasmas, but also provide further insight into the mechanisms responsible for the acceleration of the 3 He ions in 3 He-rich solar flares. 18 These events are characterized by an enormous enrichment of the rare isotope 3 He (by a factor of $10 4 ) above the solar wind or coronal abundances. 22,23 Various models have been proposed to explain the anomalous abundance of highly energetic 3 He ions. Most of the developed models are based on the ion cyclotron resonance with plasma waves, assumed to be generated by an electron current, energetic electron beams or via coupling with lowfrequency Alfv en waves. 23 Our studies show that if proton plasmas additionally include 4 He ions at the level of n( 4 He)/n e % 10%-15%, the ion cyclotron absorption by a small number of 3 He ions can be strongly increased. 18 The paper is organized as follows. In Sec. II, we discuss the theoretical background and provide practical recipes for selecting the plasma composition and resonant absorbers. This is followed by a summary of the main results from proof-of-principle experiments in H-D plasmas in JET and Alcator C-Mod. Section III summarizes recent progress with extended applications of these novel scenarios in H-D, H-4 He, and D-3 He plasmas on AUG and JET. The insights gained over the last few years also provide a common framework to explain puzzling results in some past fast-ion ICRF experiments in D-3 He and D-T plasmas in JET and TFTR, discussed in Sec. IV. Section V follows with an overview of promising applications in fusion research, including D-T and nonactive plasmas in ITER. Summary and conclusions are presented in Sec. VI.

II. PROOF-OF-PRINCIPLE EXPERIMENTS IN H-D PLASMAS USING THERMAL 3 HE AND FAST D-NBI IONS AS RESONANT ABSORBERS IN THE PLASMA CORE
A. Transforming mode conversion electron heating into a flexible ion cyclotron heating scenario in multiion species plasmas: Theoretical background A basic understanding of fast wave (FW) propagation characteristics in multi-ion species plasmas can be obtained from the coldplasma dispersion relation, defining the perpendicular FW refractive index (with respect to the confining magnetic field) Here, S , L , and R are the plasma dielectric tensor components in the notation of Stix 13  , the local damping rate P abs =S ? is enhanced in regions where the conditions L ¼ n 2 k and S ¼ n 2 k are satisfied.
A plasma with N ion species with a different charge-to-mass ratios has N À 1 successive pairs of ion cyclotron resonances. Between every such pair of cyclotron resonances, there exists a solution for the equation S ðx S Þ ¼ n 2 k and L ðx L Þ ¼ n 2 k , defining the cold-plasma fast wave resonance and the left-hand cutoff, respectively. Throughout the paper, we adopt the notations "IIH resonance" 24 and "IIH cutoff" for the corresponding FW resonance and left-hand cutoff, and use the term "IIH layer" to loosely refer to the region with the enhanced E þ and wave damping around this cutoff-resonance pair. Note that hot-plasma effects impact the FW dispersion, in particular, by bending the FW resonance into a confluence with a kinetic mode. Yet, the cold-plasma approximation is still rather accurate to determine the position of the IIH layers in multi-ion species plasmas.
For example, in two-ion species plasmas and for low k jj , the IIH cutoff and resonance frequencies are given by 25 where x p1 and x p2 are the plasma frequencies for the two ion species. For these plasmas Z 1 X 1 þ Z 2 X 2 ¼ 1, and the equation for the IIH cutoff frequency can be simplified further to Here, Z 1 and Z 2 are the charge numbers and X 1 and X 2 are the ion concentrations. It is immediately clear that the position of the IIH cutoff can be controlled by varying the plasma composition and that x L is located in between x c1 and x c2 . An expression with similar characteristics can be derived for x S . For the more general case with N plasma ion species with a different charge-to-mass ratio, the exact plasma composition has to be taken into account to calculate the locations of the N À 1 IIH layers (not necessarily all located in the plasma). At sufficiently large concentrations of the minority ion species, the distance between the IIH layer and the minority cyclotron resonance becomes too large such that minority ions can no longer resonate in the vicinity of the region with enhanced jE þ j and electron heating via mode conversion is usually realized. 12,15 By extending the plasma composition, three-ion ICRF scenarios offer a method to transform local electron heating via mode conversion into an effective technique for ion cyclotron heating in multi-ion species plasmas with a range of applications, as discussed in this paper.
In what follows, we use Z i and A i for the charge number and the atomic mass of ion species i, with indices "1" and "2" for the nonresonant main ions such that (Z/A) 2 < (Z/A) 1 (i.e., ion species #1 has a larger cyclotron frequency than #2) and index "3" for the resonant absorber population. We also use X i ¼ n i /n e as the notation for the ion concentrations, where n e is the electron density. As resonant absorbers, a third ion population with a (Z/A) value "sandwiched" between that of the two nonresonant ions, (Z/A) 2 < (Z/A) 3 < (Z/A) 1 was proposed in the original theoretical formulation of this ICRF scenario. As discussed in Refs. 17 and 18 and as follows from Eq. (4), efficient ion cyclotron absorption by the third ion population at very small concentrations is maximized at 3 À ðZ=AÞ 2 ðZ=AÞ 1 À ðZ=AÞ 2 : In this case, concentrations of resonant absorbers as low as a few & are sufficient to absorb nearly all launched RF power, allowing to maximize the absorbed RF power per resonant ion and, thus, the efficiency of fast-ion generation. This operational space is not readily available for the commonly used minority scenarios, typically being the most effective at minority concentrations of a few %. Note that plasma heating with three-ion ICRF scenarios at larger concentrations of resonant ions is equally possible: in this case, plasma mixtures with X 1 տ X Ã 1 and X 2 Շ X Ã 2 are more optimal for fast waves excited from the low magnetic field side (LFS). 26 Fast ions with the same (Z/A) as one of the main plasma ions can also be used as resonant absorbers. 19,20 A natural choice for the realization of the Doppler-shifted version of the three-ion

REVIEW
scitation.org/journal/php ICRF scenario are fast ions injected by neutral beam injection (NBI). Note that the same physics applies to energetic ions that are products of fusion reactions, as, e.g., fusion-born alpha particles. Absorption of ICRF power by highly energetic alpha particles in D-T plasmas is commonly considered as a parasitic effect to be avoided, but it has a potential to be used to advantage, as discussed in Sec. V D.
For simplicity, we consider plasmas where the resonant fast ions have the same charge-to-mass ratio as ion species #2 according to the adopted definitions, i.e., (Z/A) 2 < (Z/A) 1 . In this case, the IIH layer is located in the low magnetic field side direction with respect to the cyclotron resonance of ion species #2. This implies that fast ions with a positive Doppler shift (k jj v jj >0) are required to resonate at this layer. Efficient RF power absorption by fast ions is realized in plasmas with a composition given by Here, p ¼ dR ðmaxÞ fast =R abs , R abs is the intended radial location for RF power absorption (for core heating R abs % R 0 ), dR x is the Doppler-shift distance for fast ions with maximum parallel velocities, and n tor is the fast wave toroidal mode number, k jj % (B tor /B) (n tor /R). The factor B tor /B in these expressions ensures the proper sign for k jj and dR fast along the magnetic field, regardless the choice for the orientation of the toroidal angle. Using the formal substitution one easily finds the equivalence of Eqs. (5) and (6). This equivalence further highlights the main idea behind three-ion ICRF scenarios: extending the plasma composition beyond two ion species to include an additional population of ions capable to satisfy the resonance condition, Eq. (1) at the location of the IIH layer. One can easily derive similar formulas when the resonant fast ions have the same charge-to-mass ratio as ion species #1, i.e., those with (Z/A) 1 > (Z/A) 2 . Then, the IIH layer is located toward the high magnetic field side (HFS) direction with respect to the cyclotron resonance of ion species #1 and fast ions with a negative Doppler shift (k jj v jj <0) are required to resonate at this layer.
We also introduce the following notation for three-ion ICRF scenarios: Y 2 -(Y 3 )-Y 1 , where the resonant absorbers Y 3 are indicated between the round brackets, and Y 2 and Y 1 are the nonresonant ions ordered according to their (Z/A) value (x c2 < x c1 ). For example, the notations D-( 3 He)-H and D-(D NBI )-H stand for three-ion ICRF scenarios in mixed H-D plasmas, using 3 He and D-NBI ions as resonant absorbers, respectively.

B. Proof-of-principle experiments with resonant 3 He ions in mixed H-D plasmas on Alcator C-Mod and JET
Mixed H-D plasmas with 3 He ions as resonant absorbers (with their unique (Z/A) ¼ 2/3) were chosen for the proof-of-principle demonstration of these novel ICRF scenarios on the Alcator C-Mod and JET tokamaks. As reported in Ref. 18, the experimental studies on Alcator C-Mod were performed at a very high toroidal magnetic field B 0 ¼ 7.8 T, plasma current I p ¼ 1.2 MA and high central electron densities n e0 % 2-3 Â 10 20 m À3 . 4-5 MW of ICRF power was delivered into this plasma at RF frequencies f ¼ 78.0-80.0 MHz for the core 3 He heating. Figure 1 shows the time evolution of the ICRF power, central electron temperature T e0 , and plasma stored energy W p for a pulse with the 3 He minority scenario in a D plasma (X[ 3 He] % 5%-7%, black dotted lines), and a pulse with the three-ion D-( 3 He)-H scenario in a H-D plasma (X[ 3 He] % 0.5%, red solid lines). The high efficiency of the three-ion ICRF scenario for plasma heating is clearly seen by comparing the time traces for T e0 and the plasma stored energy at the same RF power, P ICRF ¼ 4 MW. The novel ICRF scenario was also effective in generating highly energetic 3 He ions in the plasma, as testified by an increased sawtooth period (the presence of fast ions is well known to have a stabilizing effect on sawteeth 27 ) and the excitation of Alfv en eigenmodes (AEs). 18 The high efficiency of this novel ICRF scenario was independently confirmed on the world-largest tokamak currently in operation, JET (R 0 % 3 m, a % 1 m). Due to its larger size and higher plasma current, multi-MeV 3 He ions are well confined in JET and, thus, effective plasma heating was achieved at even lower 3 He concentrations than in Alcator C-Mod. Figure 2(a) shows an overview of JET pulse #90758 (3.2 T/2 MA, n e0 % 4 Â 10 19 m À3 , f ¼ 32.2-33.0 MHz), where n( 3 He)/n e % 0.2% was successfully controlled by the 3 He real-time control system (RTC), measuring its concentration at the plasma edge. 12,28 Multi-MeV range 3 He ions were generated in those experiments, as confirmed by a suite of fast-ion diagnostics at JET, including gamma-ray spectroscopy. 29 Similar to Alcator C-Mod results, long-period sawteeth and 3 He-driven tornado toroidicity-induced AE (TAE) modes 30 were observed in JET experiments. Figure 2(b) illustrates that the three-ion ICRF scenario is also efficient for plasma heating at higher 3 He concentrations (#90756). At the start of this pulse, the 3 He concentration was kept at a very low level $0.2% by the 3 He RTC system. The measured T e and T i profiles highlight that not only electrons, but also bulk ions were effectively heated [not shown here; see Fig. 3(b) in Ref. 31]. As the concentration of 3 He ions was gradually increased to $1.5%, efficient plasma heating continued to be observed, demonstrating the robustness of the heating scenario to variations in n( 3 He)/n e within this range and to inherent uncertainties with measuring the 3 He concentration in the core regions of the plasma. Although JET has a limited experience with the application of this scenario at 3 He minority concentrations of $1%, these first results are encouraging.
JET also demonstrated effective plasma heating with this novel scenario, when NBI was not available and the plasma was heated by ICRF only. A clear illustration is shown in Ref. 32, where JET pulse #91304 (3.1 T/1.8 MA, P ICRF % 4.4 MW, þp/2 phasing) and the corresponding fast-ion observations are discussed in detail. In that pulse, not only tornado TAEs, but also ellipticity-induced AE (EAEs) were excited by multi-MeV 3 He ions generated with the three-ion ICRF scenario.

Physics of Plasmas
REVIEW scitation.org/journal/php efficiency of the three-ion D-(D NBI )-H ICRF þ NBI scenario. 19,20 In this case, the radial location of the IIH layer is actively controlled by properly selecting the concentrations of the H and D ions, while the role of NBI system is to provide resonant absorbers at the IIH layer. Thus, the (Z/A) value of the resonant NBI ions can be the same as for the main plasma ions. In these proof-of-principle JET experiments, a combination of D-NBI (E NBI % 100 keV, tangential injectors with pitch k ¼ v jj /v % 0.62), and ICRF heating (f ¼ 25.0-25.6 MHz, dipole phasing) was applied. Figure 3(a) shows an overview of JET pulse #91256 (2.9 T/2 MA, n e0 % 4 Â 10 19 m À3 controlled by the gas fueling feedback system), which is an illustrative example of what can be achieved. Following our theoretical calculations, see Eq. (6), the plasma composition (X[H] % 85%-90%, X[D] % 10%-15%) and operational settings were purposely chosen to locate the cyclotron resonance of thermal D ions HFS off-axis, while positioning the IIH layer in the plasma core. As shown in Fig. 3(a), a strong increase in T e0 and neutron rate was achieved in the combined ICRF þ NBI phases. In this pulse, the maximum neutron rate (enhanced by a factor of $10-15 with respect to the phase with NBI-only) was achieved in the phase with P NBI % 3.5 MW and P ICRF % 2.5 MW, when the isotopic ratio D/(H þ D) was $0.10. This pulse has been extensively modeled with the PION 33 and TRANSP/TORIC codes, 34,35 which compute the time-evolution of ICRF power absorption and the distribution functions of the resonant ions, as reported in Refs. 36 and 37. The observed neutron rate enhancement cannot be explained by the increase in T e alone. Indeed, the simulations show an increase in the neutron rate by a factor of $1.5-2 only, when the increase in plasma temperature is included in the simulations, but the ICRF þ NBI synergies are excluded. Figure 4 shows the distribution function of fast D ions in the core of JET plasmas in the phase of pulse #91256 with 3.5 MW of NBI and 2.5 MW of ICRF, computed by TRANSP/TORIC including the ICRF þ NBI synergies. The figure clearly illustrates the formation of high-energy D ions with energies up to $1.5 MeV, well above the NBI injection energy (E NBI ¼ 100 keV). The computed TRANSP/TORIC distribution function of energetic D ions was validated against a range of JET fast-ion diagnostics, including the total neutron rate, the time-of-flight neutron spectrometer TOFOR, the spatial neutron emission profile, and the neutral particle analyzer (NPA) measurements. 37 In fact, pulse #91256 had two combined ICRF þ NBI phases with the same total auxiliary heating power (P aux. % 6.0-6.2 MW), but different ratio P ICRF /P NBI % 0.7 and 0.3. Substantially lower neutron rates were obtained in the phase at lower ICRF power. PION modeling managed to reproduce the complex evolution of the neutron rate during the pulse at different NBI and ICRF powers. 36 In particular, the PION simulations highlighted that the ratio P ICRF /P NBI (at the total auxiliary heating power) is a strong actuator to control the fast-ion distributions generated by three-ion ICRF þ NBI scenarios. The possibility to tailor the fast-ion energy distributions from moderately high ($a few hundred keV) to very high ($1 MeV and higher) is one of the advantages of these novel scenarios. This feature is particularly relevant for studies in D-3 He and D-T plasmas by maximizing fast-ion populations at moderate energies where the corresponding fusion reactivities have a maximum. 19 For comparison, we also show the performance of JET pulse #91207 (3.25 T/2 MA, f ¼ 29 MHz) with the same radial arrangements for the ion cyclotron resonances as in pulse #91256. In both pulses, the cyclotron resonance of thermal D ions was located HFS off-axis [x cD (0)/x % 0.85-0.88] and the Doppler-shifted resonance of fast D-NBI ions was in the plasma core. Nevertheless, the results of JET pulse #91207 were quite disappointing-much lower T e0 and neutron rate-as seen in Fig. 3 In JET pulse #91255, high-energy D ions were effectively generated, when the NBI system provided resonant absorbers at the IIH layer, as seen from the time traces for the neutron rate and T e0 . When the resonant absorbers were not supplied by the NBI, the three-ion D-(D NBI )-H ICRF scenario was converted back to electron heating via mode conversion in the H-D plasma. For comparison, the left panel shows the phase with D-NBI heating only in the beginning of the discharge.

REVIEW
scitation.org/journal/php further radial shift of the IIH layer. Under these conditions, the NBI system did not provide resonant absorbers at the position of the IIH layer.
Another illustration of the importance to satisfy both conditions simultaneously is demonstrated in Fig. 5. In pulse #91255 (2.9 T/2 MA, f ¼ 25.0-25.6 MHz, dipole phasing), the isotopic ratio was nearly constant D/(H þ D) % 0.10 such that the radial position of the IIH layer remained fixed in the plasma during the pulse. The pulse was first heated with D-NBI only (t ¼ 8.0-8.6 s), leading to a relatively small increase in the neutron rate, as shown on the left panel of Fig.  5. In a later phase of the pulse, the plasma was heated with $3 MW of ICRF power only, showing an even lower neutron rate as compared to the NBI-only phase. Only when ICRF and NBI were applied simultaneously, high-energy D ions were effectively generated, leading to a strong increase in the neutron rate, T e0 and sawtooth stabilization. When NBI was again switched off at t ¼ 13.4 s, the three-ion D-(D NBI )-H ICRF scenario lacked resonant absorbers at the IIH layer and, as a result, electron heating via mode conversion in a H-D plasma was recovered. In short, the following sequence of ICRF heating scenarios was realized in JET pulse #91255: mode conversion ! ion cyclotron heating of D-NBI ions with the three-ion D-(D NBI )-H scenario ! mode conversion. This example highlights how by cleverly combining several effects that are individually well-known, one can realize a new very efficient ICRF scenario for ion cyclotron heating and fast-ion generation in mixed plasmas.

III. RECENT PROGRESS WITH APPLICATIONS OF THREE-ION ICRF SCENARIOS
In this section, we present an overview of new experimental results obtained after receiving the Landau-Spitzer Award in 2018. Significant progress has been obtained since then on JET and AUG, expanding the use of the scenarios from ICRF-dedicated studies to a flexible tool with a broad range of different applications in fusion research. Much of these recent developments were guided by the updated ITER Research Plan within the Staged Approach (2018). 38 This document reflects the ITER strategy for physics and technology research for both the Pre-Fusion Power Operation (PFPO) and the Fusion Power Operation (FPO) phases. Various three-ion ICRF scenarios were explicitly included in the document as they hold promises for both PFPO and the FPO phases of ITER.
As shown in this section, three-ion ICRF scenarios have become an important tool for the following physics topics: • Generation of fusion-born alpha particles in D- 3 He plasmas in view of the validation of JET-ILW diagnostics for alpha particle measurements in preparation for future D-T studies.

A. Demonstration of the D-(D NBI )-3 He scenario in D-3 He plasmas on JET
Following the success with the three-ion ICRF scenario to accelerate D-NBI ions in mixed H-D plasmas (see Sec. II C), the effectiveness of accelerating D-NBI ions was also demonstrated in D- 3 He plasmas on JET. 20,39 The experimental conditions (B 0 % 3.7 T, I p ¼ 2.5 MA, n e0 % 6 Â 10 19 m À3 , f ¼ 32.2-33.0 MHz, dipole phasing) were chosen such that the cyclotron resonances for thermal D and 3 He ions were located at the HFS and LFS offaxis, respectively (see Fig. 6). In these experiments, large concentrations of 3 He ions were used, n( 3 He)/n e % 20%-25% to purposely position the IIH layer in the plasma core. Similar to pulse #91256, tangential NBI injectors with E NBI % 100 keV were used to provide resonant absorbers at the IIH layer to absorb locally RF power. In this way, deuterons from the NBI system were accelerated to higher energies with ICRF in the plasma core, which leads to the generation of alpha particles from D- 3

Physics of Plasmas
REVIEW scitation.org/journal/php described here, the 3 He ions also played an active role for ICRF heating by defining the radial position of the IIH layer and thus the localization of the source of fast ions. Guided by PION modeling results, 36 the fast-ion distribution of RF-accelerated D-NBI ions in these experiments was controlled by varying the ICRF and NBI power and their ratio P ICRF /P NBI (P ICRF % 4-6 MW, P NBI % 3-20 MW). With as little as P RF % 6 MW and P NBI % 7-11 MW, rather high D-D neutron ($1 Â 10 16 s À1 ) and D-3 He alpha rates ($2 Â 10 16 s À1 ) were achieved, corresponding together to $60-70 kW of fusion power. Figure 7(a) gives an overview of JET pulse #94701, in which $8 MW of NBI was applied in combination with ICRF in steps from $4 MW to $6 MW. The panels from top to bottom illustrate P NBI and P ICRF , the line-integrated central density, the central electron temperature, the neutron rate, and the plasma stored energy. The neutron rate increased from $7 Â 10 14 s À1 in the NBI-only phase to $3.7 Â 10 15 s À1 in the first ICRF þ NBI phase with 4 MW of ICRF. Topping up ICRF power with 2 MW from the ITER-like antenna (ILA), monster sawteeth appeared, accompanied by a gradual increase in the neutron rate up to $9.4 Â 10 15 s À1 . Such a strong enhancement of the neutron rate in the ICRF þ NBI phase results from the presence of a large population of energetic D ions, further evidenced by the neutron spectrometer and NPA measurements.
We also show an overview of two other JET pulses in D-3 He plasmas at similar operational conditions, but different NBI and ICRF power. Figure 7(b) illustrates pulse #94704, in which NBI-only heating was applied in steps from $11.8 MW to $17.3 MW. Figure 7(c) shows the time traces for pulse #95683, in which the three-ion D-(D NBI )-3 He scenario was applied, but at much higher NBI power, P NBI %18.5 MW.
We first start the comparison between pulses #94701 and #94704 at the same total auxiliary heating power P aux % 14 MW. The main difference between the two pulses is the heating source. Dominant ion heating was provided with NBI-only in pulse #94704. Conversely, dominant electron heating was obtained in pulse #94701 by accelerating fast ions to energies well above the critical energy (E crit % 300 keV) using the three-ion ICRF scenario (P NBI % 8 MW, P ICRF % 6 MW). Among others, this is evidenced by the neutron In pulse #94704, NBI-only heating was applied in steps from 11.8 MW to 17.3 MW. In pulses #94701 and #95683, the three-ion D-(D NBI )-3 He scenario was applied with P ICRF % 6 MW (dipole phasing) and P NBI % 8 MW and P NBI % 18.5 MW, respectively.

FIG. 8.
A large variety of fast-ion driven AEs are regularly observed at JET, when applying three-ion ICRF scenarios to maximize core plasma heating and fast-ion generation. As an example, we show the MHD spectrogram for JET pulse #94701, in which the three-ion D-(D NBI )-3 He scenario was applied and reversed-shear Alfv en eigenmodes (RSAEs), TAEs, and EAEs were observed. The vertical dashed lines indicate the timing of the sawtooth crashes.  41 Furthermore, a rich variety of Alfv enic eigenmodes (AEs) was driven by the energetic ions in #94701, see Fig. 8. In contrast, no fast-ion driven AEs were observed in #94704.

Physics of Plasmas
The comparison of the radial T e and T i profiles for these two pulses is shown in Fig. 9. The electron temperature profile was measured by the electron cyclotron emission diagnostic and the ion temperature profile by charge exchange recombination spectroscopy (CXRS) based on neon impurities, which were injected on purpose for T i measurements. The stronger T e peaking, the much higher T e0 and neutron rate in pulse #94701, as compared to #94704, are easily understood by the presence of high-energy D ions. Interestingly, very similar ion temperatures were reached in these two pulses, despite the substantial difference in the ion/ electron heating sources. The comparison of the measured T e and T i profiles and the plasma stored energy [cf. Figs. 7(a) and 7(b)] hints at better plasma confinement in pulse #94701. Characterized by a large fraction of energetic ions in the plasma core, the heating conditions in #94701 approach those expected in burning plasmas of ITER with alpha particles. Despite dominant fast-ion electron heating in #94701, T i % T e was observed, which is very promising in view of ITER. This experimental observation is supported by the detailed gyrokinetic analysis of #94701 with the GENE code, 42 showing that the ion-temperature-gradient (ITG) driven turbulence was suppressed in the presence of MeV ions and fully destabilized TAEs, see Ref. 41. The application of three-ion ICRF scenarios as a tool for turbulence studies, in particular, to study the complex interplay between microturbulence, fast ions, and MHD modes, is further outlined in Sec. V A.
Next, we compare pulses #94701 and #95683 with a similar ICRF power (P ICRF % 6 MW), but very different NBI power (P NBI ¼ 8.1 MW vs 18.4 MW). As seen in Figs. 7(a) and 7(c), the achieved neutron yield, T e (0) and the plasma stored energy are very similar, although there is a rather significant difference in the total auxiliary heating power ($14 MW vs $24 MW). These results underline the decisive role of ICRF to accelerate ions to high energies and the associated fastion effects on the plasma, including neutron generation.

B. Efficient generation of passing fast ions and fast-ion current drive
Reversed-shear Alfv en eigenmodes (RSAEs) 43 were regularly observed in this series of fast-ion experiments in D-3 He plasmas (3.7 T/2.5 MA) with n( 3 He)/n e % 20%-25% and D-NBI ions as resonant absorbers. RSAEs were particularly pronounced during the phases with long-period sawteeth, sufficiently long to track the temporal evolution of the frequency of these modes, starting from the geodesic acoustic mode frequency (somewhat below $100 kHz) up to the TAE frequency ($200 kHz). Figure 10 illustrates the excitation of RSAEs with toroidal mode numbers n ¼ 3, n ¼ 2 and n ¼ 1 in JET pulse #94701 during the sawtooth cycle t ¼ 9.42-11.17 s. To corroborate this result, we also show the excitation of RSAEs in the other JET pulse #95667 (Fig. 11) with a constant NBI power P NBI % 5.4 MW and two levels of ICRF. The sawtooth period extended from Dt saw % 0.6 s (t ¼ 7.83-8.44 s) at P ICRF % 4.1 MW up to Dt saw % 3.5 s (t ¼ 8.44-11.94 s) at P ICRF % 5.8 MW. The bottom panel clearly illustrates the presence of RSAEs in this pulse as well. In particular, a very strong RSAE mode with n ¼ 1 is seen in the Mirnov coil spectrogram. An interesting observation in #95667 is that the neutron rate is continuously increasing while the RSAE modes are seen and starts to decrease after the disappearance of the RSAEs. The regular observation of RSAEs in these experiments indicates that a nonmonotonic q-profile was developed and sustained during the application of the three-ion D-(D NBI )-3 He scenario. Note that no RSAEs were seen in the heating phases with NBI-only.
In this section, we show that energetic D ions accelerated with the three-ion ICRF scenario in JET experiments remain co-passing ions. This is because of the combination of the strong localization of RF power deposition in the plasma core, nonstandard fast-ion orbit topology in that region and the quasilinear evolution of the fast ions. We note that the strong localization of RF power deposition and strong jE þ j in a small volume is a particular feature of three-ion ICRF scenarios, when they are tuned for maximizing fast-ion generation in the plasma center of large devices such as JET. This was already shown for the three-ion D-(D NBI )-H scenario in Fig. 10

REVIEW
scitation.org/journal/php distribution of the RF electric field jE þ j 2 over the plasma cross section. This characteristic is further illustrated in Fig. 12(a) for the three-ion D-(D NBI )-3 He scenario (JET pulse #94701), confirming the strong core localization of ICRF-accelerated fast D ions. The boundary separating trapped and passing ions is commonly given by the simplified expression k Ã ¼ 6 ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2r=ðR 0 þ rÞ p , 14 but this approximation is not valid here. In fact, as shown in Fig. 12(b), the trapped-passing boundary in the plasma region close to the magnetic axis has a very different structure (dashed lines) such that virtually all fast ions with v jj > 0 stay on co-passing orbits, even at high energies. This reasoning applies for both thermal and fast ions as resonant absorbers, accelerated by threeion ICRF scenarios in JET.
To quantify this effect for three-ion ICRF scenarios with fast NBI ions as resonant absorbers we recall that according to the quasilinear theory, [44][45][46] the cyclotron interaction of resonant ions with RF waves not only changes the energy of the particles, but also causes a change of their pitch and a displacement of their orbits. Because of the strong core localization of the fast-ion generation for centrally tuned threeion ICRF scenarios, we ignore the orbit displacement effects and focus on analyzing how the pitch of the resonant ions changes as they are accelerated to MeV-range energies with ICRF. Following Refs. 45 and 46, we note that where E is the kinetic energy, K ¼ lB 0 /E is the normalized magnetic moment, K ¼ (1 À k 2 )B 0 /B, and K 1 ¼ x ci (0)/x. With these approximations, one can easily derive from Eq. (9) that kðEÞ ¼ ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ffi

Physics of Plasmas
REVIEW scitation.org/journal/php with k 2 1 ¼ 1 À K 1 ; k 0 and E 0 are the initial pitch and energy of resonant ions. Equation (10) provides an estimate for the change in the pitch of the resonant ions, as they absorb RF power and are accelerated to higher energies.
In these JET experiments in mixed H-D and D-3 He plasmas using D-NBI ions as resonant absorbers, 19,20,39 the IIH layer was on purpose located in the plasma core, in turn, implying that the cyclotron resonance for thermal D ions was positioned at the HFS off-axis (see Fig. 6), K 1 ¼ x cD (0)/x % 0.85-0.89. Thus, according to Eq. (10), the asymptotic value of the pitch parameter of the ICRF-accelerated D ions reaches k 1 % 0.34-0.38. The evolution of the pitch-parameter of resonant ions as given by Eq. (10) is plotted with a red solid line in Fig. 12(b). The red dotted line shows the extreme (unphysical) case, where resonant NBI ions would only increase their perpendicular energy. Even then, the fast ions remain co-passing as a result of the unusual shape of the trapped-passing boundary in the plasma core. This result is supported by TRANSP/TORIC simulations for the D-3 He pulse #95679 in JET. Figure  At first sight, it might look contradictory to generate significant RF-driven currents in three-ion ICRF þ NBI experiments with a dipole ICRF antenna phasing, which has a symmetric k jj -spectrum. Usually, asymmetric ICRF antenna spectra are used for localized fastion current drive, e.g., Ref. 47. However, the three-ion ICRF þ NBI scenarios make use of the asymmetry in the v jj -distribution of the resonant absorbers (D-NBI ions). Even when using dipole phasing, this results in preferential acceleration of fast ions in the co-current direction in JET. The systematic appearance of reversed shear AEs in these fast-ion experiments indicates that the q-profile in the core region is modified or even reversed. In addition to fast-ion current drive, other mechanisms associated with the application of the threeion ICRF scenario could contribute here, as discussed in Sec. V B.
C. Toward ITER needs: Development of three-ion ICRF scenarios with off-axis heating on AUG and JET Developing techniques to control edge localized modes (ELM) and reaching the ELMy H-mode are one of the main priorities for the nonactive ITER phase. 48 In hydrogen plasmas at half magnetic field (2.65 T/7.5 MA), reaching the ELMy H-mode may be challenging, partly due to the lack of an efficient ICRF absorption scenario in such plasmas. 38,49,50 To bypass this limitation, ITER considers efficient ICRF scenarios at a toroidal field as close as possible to 2.65 T to reach the ELMy H-mode in hydrogen dominated plasmas. A possible solution is discussed in Ref. 51, where it was proposed to apply the threeion 4 He-( 3 He)-H scenario at the lowest available frequency of the ITER ICRF system, f ¼ 40 MHz in H þ 10%-15% 4 He plasmas at B 0 % 3.0-3.3 T. Under these conditions, the cyclotron resonance of 3 He ions is located at the HFS off-axis. It is important to demonstrate plasma heating with this off-axis scenario in present-day machines with a tungsten divertor such as AUG and JET. If successful, the proposed off-axis three-ion ICRF scenario would enable to provide an additional 20 MW for plasma heating. In turn, in combination with 33 MW of NBI and 20 MW heating with waves in the electron cyclotron range of frequencies (ECRF), this offers the potential to widen the H-mode operational space in predominantly hydrogen plasmas in ITER.
The first exploration of the three-ion ICRF scenario with HFS offaxis 3 He heating was conducted in H-D plasmas, H/(H þ D) % 0.8 on AUG (2.5 T/0.8 MA; f % 30 MHz, dipole phasing). AUG has an alltungsten (W) first wall and ICRF-specific W production has a strong influence on the application of high-power ICRF. The improved threestrap ICRF antennas are optimized to minimize W sputtering, in this way making ICRF compatible with a high-Z wall in AUG. 52,53 Figure 14(a) shows an overview of the heating phase of the AUG pulse #35206, combining core ECRF (1.35 MW) and the three-ion ICRF scenario with off-axis heating. Adding $1 MW of ICRF power resulted in a clear increase in the plasma stored energy and triggering the ELMy H-mode, seen in the signals for the divertor shunt currents and increase in the plasma density. Furthermore, the W concentration in the plasma, including the central region, stayed low c W < 2 Â 10 À5 (measured by two diagnostics at the radial locations corresponding to T e % 1.5 keV and T e % 3 keV). As a next step, all three heating systems were combined on AUG, as foreseen for ITER, resulting again in good heating performance and low core W levels. For more details, see the description of AUG pulse #35207 in Ref. 54.
Very recently, a first attempt with the three-ion D-( 3 He)-H ICRF scenario with HFS off-axis 3 He resonance was undertaken for plasma heating in H-D plasmas on JET-ILW. Figure 14

REVIEW
scitation.org/journal/php ICRF. In addition, the relative increase in the total radiated power before and after the application of ICRF, DP rad /P ICRF is less than 20% [see the evolution of the total radiated power, P rad shown as a dotted line in the top panel of Fig. 14(b)]. For ITER it is important to demonstrate the three-ion ICRF scenario at the magnetic field as close as possible to 2.65 T. The conditions of JET pulse #97084 closely mimic the ITER heating scenario conditions at $3.0T. This first result is promising and more studies are foreseen in future experimental campaigns on JET.
In view of ITER needs, the next essential step was the demonstration of off-axis three-ion ICRF heating in nonactive H-4 He plasmas. This was pioneered with success on AUG in the summer of 2019. The mix of heating systems on AUG (NBI, ECRF, and ICRF) uniquely mimics that of ITER. Figure 15 shows an overview of AUG pulse #36751 (2.5 T/0.8 MA, n e0 % 4 Â 10 19 m À3 ) with a constant hydrogen NBI, P H-NBI ¼ 0.8 MW during the pulse. In the first phase of the pulse, the ECRF power was ramped up to 2.3 MW in order to trigger the L-H transition. In the second phase of the pulse with constant P H-NBI ¼ 0.8 MW and P ECRF ¼ 0.8 MW, ICRF power was added and ramped up to 1.6 MW, again leading to the L-H transition. This confirms that the mix of hydrogen NBI, ECRF, and ICRF using the three-ion scenario with off-axis deposition of RF power can also be applied to trigger ELMs in these ITER-relevant H-4 He plasmas. Furthermore, L-H transitions and ELMy H-mode phases in H-4 He plasmas were realized with ECRF þ ICRF and ICRF-only on AUG. For this series of AUG experiments with off-axis three-ion ICRF heating, L-H transitions were generally reached at P LH % 2-3 MW, which is similar to earlier observations with hydrogen NBI and ECRF heating in H-4 He plasmas on AUG. 55 The fact that tungsten levels stayed low in these ICRF experiments on AUG is encouraging in view of possible application of this integrated heating scenario in ITER. Further studies of this ITER-relevant heating scenario in H- 4 He and H-D plasmas are foreseen on AUG.

D. Optimization of fast-ion studies with three-ion ICRF scenarios on AUG
In AUG, the application of the three-ion ICRF scenario with onaxis 3 He resonance at extremely low concentrations, n( 3 He)/n e % 0.2% did not show such clear signs of plasma heating as in JET. The reason for this difference is the reduced confinement of MeV-range ions in AUG, as compared to JET, because of the smaller machine size and smaller plasma currents. While JET is capable to confine most of the fast 3 He ions with energies of a few MeV, 3 He fast-ion energies in AUG should be limited to $1-1.5 MeV to have sufficient time to transfer their energy to the background plasma during the slowing down. In order to reduce the energies of fast 3 He ions, and thus improve the confinement of the ICRF-heated 3 He ions on AUG, an obvious solution was to reduce the absorbed RF power per resonant ion.
Higher 3 He concentrations of $0.5%-1% were more optimal for on-axis heating of medium-size AUG plasmas. Figure 16(a) shows an overview of AUG pulse #34695 with the 3 He resonance on-axis (3.0 T/ 0.8 MA, f ¼ 30 MHz, dipole phasing). This illustrates the increase in the plasma stored energy and plasma temperature after switching on the ICRF system at t ¼ 1.4 s. The corresponding T e and T i profiles are shown in Fig. 16(b). Unfortunately, central electron temperature data are not available for AUG discharges at 2.8-3.0 T, making the analysis of the peakedness of the T e profile rather difficult. The fact that energetic 3 He ions were sufficiently well confined in this pulse follows from the evolution of the plasma stored energy, increasing from 200 kJ in the NBI-only phase to $300-310 kJ in the ICRF þ NBI phase. Generation of energetic 3 He ions with on-axis ICRF resonance was

REVIEW
scitation.org/journal/php also observed in AUG plasmas, confirmed by the excitation of Alfv enic modes (f AE % 160-190 kHz), the appearance of fishbones and by fast-ion loss detector (FILD) measurements, shown in Fig. 17(a). The backward-orbit tracing of escaping ions measured by FILD was undertaken for H, D and 3 He ions, as shown in Figs. 17(b)-17(d), and infers that the measured escaping ions originate from the plasma core. The backward-traced orbits for energetic 3 He ions are consistent with the 3 He ICRF resonance located in the plasma core. The fast-ion energies can be estimated using the following formula: where q L is the Larmor radius of escaping ions measured by FILD and B FILD is the magnetic field strength at the position of the detector. Using Eq. (11) with B FILD % 2.3 T for #34695, one finds that the measured fast ions with q L ¼ 7 cm correspond to 3 He ions with energies of $1.7 MeV. Alternatively, one can also reduce the energies of the generated fast 3 He ions by shifting the resonance location off-axis. In this way, the same amount of RF power is deposited in a larger volume, thus, reducing RF power per resonant ion. This was applied successfully in AUG pulse #34704 (n( 3 He)/n e % 0.5%-1%) by reducing the toroidal magnetic field to 2.8 T and shifting the 3 He cyclotron resonance to q pol % 0.3 at the HFS. As shown in Fig. 18, ICRF power was increased in three steps: 0.9 MW, 1.9 MW, and 2.5 MW. Consequently, the plasma stored energy increased from $300 kJ during the NBI-only phase with P NBI ¼ 8 MW to $400 kJ during the ICRF þ NBI phase. The TORIC-SSFPQL modeling 56 of this pulse showed that the perpendicular temperature of RFheated 3 He ions reached $500 keV in the phase with P ICRF ¼ 2.5 MW, see Refs. 57 and 58. A gradual increase in T e measured at q pol % 0.2 seen in Fig. 18 is consistent with the fact that energetic 3 He ions transfer most of their energy during their slowing-down to the electrons. CXRS measurements confirmed the presence of confined energetic 3 He ions in the plasma. 57,58 The magnitude of the predicted charge exchange spectral radiance, obtained via forward-modeling of the spectrum utilizing TORIC-SSFPQL distribution functions, and the expected energies of the ions agree well with the measurement, confirming that the spectral feature is due to ICRF-accelerated 3 He ions, as reported in Ref. 58. These examples illustrate that three-ion ICRF scenarios at very low concentrations of resonant absorbers can be effectively used to probe the limits of fast-ion confinement in fusion devices. Indeed, our experience with the development of on-axis heating of AUG plasmas with this scenario highlights that it can easily generate fast ions that are too energetic to be confined in this tokamak. Therefore, pushing for the maximum efficiency of fast-ion acceleration [e.g., on-axis ICRF resonance and very low n( 3 He)/n e ] in smaller-size machines does not necessarily maximize the number of confined fast ions in the plasma and,

REVIEW
scitation.org/journal/php in fact, can lead to disappointing results. In such a case, a careful optimization of the scenario parameters (e.g., plasma composition, resonance location, antenna phasing, etc.) is needed to maximize the content of confined fast ions.

IV. A COMMON FRAMEWORK TO EXPLAIN EARLIER EXPERIMENTAL RESULTS WITH ICRF HEATING IN MIXED PLASMAS A. Unexpected RF power absorption by impurities in D-T experiments in TFTR and JET
In TFTR, the success of mode conversion experiments for localized electron heating and current drive in D-3 He plasmas motivated the team to apply this ICRF scenario also in D-T plasmas.
However, in the experiments only $20% of the incoming RF power heated the electrons, in contrast to what was expected, see Fig. 19 (reprinted from Ref. 21). The low efficiency of mode conversion electron heating was attributed to the presence of a small amount of 7 Li ions, n( 7 Li)/n e % 0.5%, absorbing most of the launched RF power. The 7 Li ions originated from the use of natural lithium pellets (note that 7 Li constitutes 92.5% of naturally occurring lithium) to condition the TFTR wall in those D-T experiments. Supported also by numerical modeling, it was soon realized that $80% of RF power was absorbed by 7 Li ions, despite their low concentrations. In fact, the three-ion T-( 7 Li)-D ICRF scenario was effectively at work and 7 Li ions absorbed RF power near one of the IIH layers located close to the cyclotron resonance of 7 Li.
In their paper, 21 the authors discussed all essential elements, in particular, the enhanced left-hand RF polarization at the IIH layer, and explained the mechanism behind the observed strong impurity absorption. However, as the ICRF resonance of the 7 Li ions was located LFS off-axis for the chosen conditions, the absorption was considered as a parasitic effect, preventing the RF power to reach the

REVIEW
scitation.org/journal/php plasma core. To eliminate this unwanted 7 Li absorption, isotopically 6 Li-enriched pellets were used in the next series of D-T experiments and electron mode conversion heating was recovered. As 6 Li ions have the same Z/A ¼ 1/2 ratio as D ions, they cannot act as a third resonant absorber in D-T plasmas. Tungsten and beryllium have been chosen as the plasma-facing components for JET-ILW and ITER, resulting in a non-negligible amount of 9 Be impurities in the plasma. In JET-ILW, typical concentrations of 9 Be are usually about $0.5%-1%. In their publication, 21 the TFTR team also correctly highlighted that strong ICRF damping on 9 Be impurities will arise in ITER D-T plasmas, and that this would lead to effects similar to their observations with 7 Li. However, our developments show that the unwanted "parasitic" absorption by 7 Li and 9 Be ions could be easily converted into an efficient scenario for bulk ion heating in JET-ILW and ITER D-T plasmas. 26,59,60 Another important outcome of the analysis by the TFTR team was the conclusion that mode conversion heating in D-T plasmas in the frequency range x cT < x < x cD is not consistent with 9 Be plasma-facing components, unless the level of 9 Be can be kept very low. 21 Indeed, as follows from detailed numerical analysis for ITER in Ref. 59, already at 9 Be concentrations as low as $0.1%-0.2% most of RF power will be absorbed by these intrinsic impurities via the threeion T-( 9 Be)-D scenario, thereby preventing mode conversion heating in D-T ¼ 50%-50% plasmas and thus also the use of mode converted ion Bernstein waves (IBW) for other applications.
There was a similar puzzling observation in D-T ICRF experiments in JET with the carbon wall, when the deuterium concentration was varied between 9% and 22%. 61 It was reported that while the largest fusion yield was reached at 9% of D, strong bulk ion heating occurred at 18% of D, with a $60% contribution from the thermal fusion reactions to the total neutron yield. Strong ICRF damping on $1.5% 9 Be impurities in D-T plasmas, amplified by the large E þ at the IIH layer, was put forward as one of the possibilities to explain the observations. The conclusion was that under those experimental conditions, 9 Be impurities can absorb up to 40% of the incoming RF power. In fact, all the essential elements for the three-ion ICRF scenario in D-T plasmas with 9 Be as resonant absorbers were described in Ref. 61. We note that in D-T ¼ 50%-50% plasmas ICRF power absorption by 9 Be impurities is even more effective.

B. Efficient acceleration of D-NBI ions in D-3 He mode conversion experiments in JET-C and TFTR
A competing damping mechanism was observed in D-3 He ICRF mode conversion experiments with n( 3 He)/n e % 25%-35% on JET with the carbon wall (JET-C), in the presence of fast D-NBI ions (E NBI % 135 keV). At such large 3 He concentrations (above the optimal one for mode conversion), energetic D ions were observed, evidenced by the strong increase in the neutron yield, the intensity of the gamma-rays and long neutron decay times after the D-NBI blip: see Sec. 2.2 in Ref. 12 for a detailed discussion. This effect was also later observed in JET-C ICRF experiments in D-3 He plasmas with n( 3 He)/n e % 20%, as reported in Ref. 28.
It is well known that mode converted IBWs are characterized by much larger perpendicular wavenumbers than fast waves. As a result, interaction between ions and IBWs cannot lead to the generation of populations of MeV-range ions. Thus, the clear experimental observation of fast D ions with energies significantly above the NBI injection energy is proof of an efficient transfer of RF power from the launched fast waves rather than from mode converted IBWs. Fulfilling the resonance condition, Eq. (1) for fast D-NBI ions at the IIH layer was realized by the authors of Ref. 12 as the mechanism responsible for the observed efficient generation of high-energy D ions. In one of the comparison shots, the 3 He puff was replaced by a similar 4 He puff, resulting in a strong reduction of the 3 He concentration and an associated shift of the IIH layer. Thus, the fast D-NBI ions were no longer resonating at the IIH layer, leading to the disappearance of highly energetic D ions in the plasma.
Note that similar observations were also made in ICRF experiments in D-3 He plasmas on TFTR 62 in the presence of D-NBI heating. At large n( 3 He)/n e % 20% strongly enhanced fastion losses were observed, considered to be either D-D fusion-born tritons or ICRF-accelerated D-NBI ions. The results of our recent JET-ILW experiments in D- 3 He plasmas proved that D-NBI ions can be effectively accelerated to high energies by the launched fast waves in the vicinity of the IIH layer. As follows from ICRF modeling, at these conditions only a few % of the incoming RF power reaches the point where fast waves undergo mode conversion to IBWs.
In fact, recent fast-ion studies in JET-ILW D-3 He plasmas with n( 3 He)/n e % 20%-25% using the three-ion D-(D NBI )-3 He scenario, as described in Secs. III A and III B, is a natural follow-up of those earlier experiments in JET-C and TFTR. The enhanced set of fast-ion diagnostics now available at JET, combined with the progress with the development of heating and transport modeling codes, allows a much more detailed understanding of the complex physical processes, taking place in these mixed D- 3 He plasmas.
C. The importance of residual D ions and intrinsic carbon impurities for 3 He ICRF experiments in H plasmas on AUG and JET with a carbon wall A series of 3 He minority and mode conversion experiments in H majority plasmas were undertaken on the AUG and JET tokamaks, both with a carbon wall at the time of the experiments. 15,[63][64][65] Both studies highlighted that for the correct interpretation of the experimental results, including the presence of additional ion species with (Z/A) ¼ 1/2 is essential. All ions with (Z/A) ¼ 1/2 contribute to an equivalent total concentration of D ions where the contributions from D, 4 He 2þ , and 12 C 6þ ions are explicitly taken into account, and the last term includes the sum over all other ion species in the plasma with Z/A ¼ 1/2. In ICRF experiments on AUG with the carbon wall, 63 the concentration of residual D ions was $15%. Similar equivalent concentrations of D ions (X[D] equiv. % 14%-20%) were reached in ICRF experiments in JET-C plasmas 15 that contained $2%-3% of intrinsic carbon impurities and $2% of residual deuterium. Thus, from the ICRF point-of-view, those plasmas were equivalent to an H-D mix with n(D)/n e % 15%-20% and correspondingly n(H)/n e % 80%-85%.
In fact, the isotopic H-D ratio in recent three-ion ICRF experiments on Alcator C-Mod, JET and AUG with resonant 3 He ions closely mimicked the conditions achieved in earlier 3 He ICRF experiments in hydrogen plasmas on AUG and JET-C. The authors of Refs. 15 and 63-65 clearly realized and highlighted the importance of residual D ions and carbon impurities, and their impact on the details of RF wave propagation and power absorption under those experimental conditions. New developments highlight the potential to exploit the presence of intrinsic and extrinsic impurities in the plasma, as an active element to control ICRF power deposition and fast-ion generation.

V. PROMISING APPLICATIONS FOR FUSION RESEARCH
As follows from the discussions in Secs. II-IV, for almost any mixed plasma, including D-T, one can find a corresponding three-ion ICRF scenario for a specific task. This section describes practical applications of these novel ICRF scenarios beyond plasma heating and fastion generation, which have a promising potential for fusion research, but are still largely under development.

A. A tool for the fast-ion driven MHD modes and turbulence studies
Dominant core electron heating from fusion-born alphas will be the main source of plasma heating in future D-T experiments. Recent theoretical studies highlight that alpha particles can significantly stabilize ITG turbulence and reduce heat transport in ITER. 66 Thus, developing heating scenarios in present-day tokamaks that closely mimic the conditions of fast-ion electron heating representative for ITER plasmas is very important to obtain a deeper understanding of the expected impact of the fusion-born alphas in D-T plasmas and validate existing state-of-the-art microturbulence codes with the data obtained.
Furthermore, fusion-born alpha particles in D-T plasmas in ITER are expected to destabilize Alfv en eigenmodes, possibly leading to detrimental effects on plasma confinement. 67 In view of ITER, several fast-ion scenarios have been developed on different machines in recent years to excite AE modes and study the mechanisms for their control. 68 As discussed in Sec. III A, a large variety of Alfv enic modes such as TAEs, RSAEs, and EAEs are regularly observed in JET experiments with three-ion ICRF scenarios optimized for core heating and fast-ion generation, see Fig. 8.
Surprisingly, in most cases, the observed complex AE activity was not detrimental for plasma confinement in three-ion ICRF studies on JET. Recent gyrokinetic analysis of these experiments in D-3 He plasmas and its comparison with the NBI-only pulse #94704 highlights that efficient ion heating can be reached in the presence of MeV-range fast ions and fully destabilized TAEs seen experimentally through a complex multi-scale mechanism that generates intense zonal flows. 41 This mechanism is promising to reach high T i in future fusion plasmas with strong electron heating by the alpha particles. Note that the suppression of the electrostatic turbulence with moderately energetic fast ions ($100 keV) in the presence of marginally stable TAEs, appearing in the gyrokinetic GENE simulations, was discussed in Ref. 69.

B. A tool to modify the q-profile in the plasma core
Reversed-shear Alfv en eigenmodes were regularly observed in JET experiments with the three-ion ICRF scenario in D-3 He plasmas, as discussed in Sec. III B (see also Figs. 10 and 11). This indicates that the application of this fast-ion scenario with associated phenomena led to a modification of the q-profile. Several mechanisms could contribute. First, three-ion ICRF scenarios on JET generate a population of co-passing fast D ions and fast-ion current drive, but not necessarily peaked exactly on-axis. This could be caused by, e.g., the Shafranov shift of the magnetic axis and variations of the plasma composition, defining the exact location of the IIH layer. Second, the significantly higher T e0 reached during the phases with ICRF increases the number of fast ions in the slowing-down population as n fast / T 3=2 e [e.g., in pulse #94701 T e0 doubled from $3.5 keV during NBI-only to $7.0 keV during the combined ICRF þ NBI phase, see Fig. 7(a)]. Furthermore, the strongly peaked pressure profile also leads to an increased bootstrap current contribution. All these simultaneously appearing effects are a direct consequence of the application of the three-ion ICRF scenario. The detailed understanding of the interplay between various mechanisms, leading to systematic observations of RSAEs, is a subject of ongoing active research. In this context, it is important to mention that RSAEs were also observed in three-ion ICRF experiments on JET in H-D (and very recently in H-4 He) plasmas with thermal 3 He ions as resonant absorbers, when using co-current drive ICRF antenna phasing. These experimental results illustrate that three-ion ICRF scenarios have the potential to become a control tool to modify the q-profile in the central region of the plasma.

C. Bulk ion heating in D-T plasmas
Second harmonic heating of tritium ions is considered as the main ICRF scenario for D-T plasmas in ITER, facilitated by the injection of a few percent of 3 He ions to maximize bulk ion heating and to increase T i during the ramp-up phase of the pulse. Because 3 He is a scarce gas, using the three-ion T-( 9 Be)-D scenario with a small amount of intrinsic 9 Be impurities ($1%) as resonant absorbers was proposed for RF heating in D-T ¼ 50%-50% plasmas. 59 In fact, 9 Be impurities are the dominant channel of RF power absorption for a fairly broad D:T range, as shown by numerical simulations in Ref. 59. As follows from basic Coulomb collision theory, 9 Be impurities have a substantially larger critical energy than 3 He ions, viz., E crit ( 9 Be) % 74 T e vs E crit. ( 3 He) % 25 T e , and thus transfer an even larger fraction of absorbed RF power to bulk D and T ions, as illustrated in Table I of  Ref. 59. This ICRF heating scenario is compatible with additional seeding of Ar and 22 Ne impurities (candidate ions for impurity seeding in ITER and future reactors 70 ) having a very similar charge-to-mass ratio as 9 Be.
We note the potential of intrinsic impurities with 1/3 < (Z/A) < 1/2, such as 7 Li and 9 Be, to absorb RF power efficiently in D-T plasmas was already experimentally observed at TFTR and JET, 21,61 as discussed in Sec. IV A. Essentially, new insights suggest that instead of considering this effect as a parasitic impurity absorption, it can be used to the benefit of future studies in D-T plasmas in JET-ILW and ITER. 26,59 D. Revisiting the parasitic absorption by alphas in D-T plasmas ICRF heating of JET-ILW and ITER D-T plasmas with intrinsic 9 Be plasma impurities in the frequency range x % x cD and below is generally quite efficient as different resonant ion populations can Physics of Plasmas REVIEW scitation.org/journal/php absorb RF power at different radial locations. These include thermal D and T ions, 9 Be and other impurities with 1/3 < (Z/A) < 1/2, injected fast D-NBI or T-NBI ions and fusion-born alpha particles. The exact split of the absorbed RF power between these components depends on the details of the selected operational settings, including the D:T ratio, ICRF and NBI parameters, plasma density and temperature, concentration of impurities, the amount of fusion-born alphas, etc. For example, at n(D)/n e % 10%, RF power is efficiently absorbed by thermal D and fast D-NBI ions in the vicinity of the D cyclotron resonance, x % x cD and at the LFS of it. In the absence of D-NBI, the high efficiency of the D minority heating scenario was demonstrated in past ICRF experiments in D-T plasmas on JET. 61 In combination with high power D-NBI, this ICRF scenario has been proposed to reach high fusion power in future D-T experiments in JET-ILW. 60,71 At higher concentrations of D ions nðDÞ=n e տ 20%-30%, RF power absorption at x % x cD becomes less efficient. A large amount of the RF power, launched from the LFS, can pass through the region x % x cD and reach the IIH layers in D-T plasmas, thus allowing to make use of the three-ion scenarios. Due to the unavoidable presence of 9 Be impurities in JET-ILW and ITER plasmas, one of the IIH layers is located in close proximity to the cyclotron resonance of 9 Be, facilitating RF power absorption by these impurities. Furthermore, simultaneously fast D-NBI ions and alpha particles can absorb RF power in the vicinity of this IIH layer (k jj v jj <0), thereby exploiting the advantages offered by the three-ion ICRF scenarios. To control the exact split of the RF power between the various resonant absorbers, different antenna phasings with different dominant values of k jj can be applied.
Absorption of ICRF power by fusion-born alpha particles in D-T plasmas is usually considered as a parasitic effect to be avoided. 72,73 The higher the plasma temperatures, the more fusion-born alpha particles are present in the plasma, leading to increased amount of RF power absorbed by these alphas and consequently reduced ICRF power absorption by 9 Be and other heavy impurities. As discussed in Secs. III B and V B, generating passing fast ions in the central regions of the plasma can be used as a tool to modify the q-profile. As the alpha distribution in D-T plasmas in ITER is to a large extent isotropic in v jj , 67 an asymmetric k jj antenna spectrum is required to generate a net noninductive current by the fusion-born alpha particles. Choosing an ICRF antenna phasing to launch RF waves predominantly in the co-or countercurrent direction might potentially be used as an additional actuator allowing to reverse the direction of the alpha-driven current. Thus, using parasitic absorption of ICRF power by alphas in the vicinity of the IIH layers in D-T plasmas might offer the potential to contribute to the control of the shape of the q-profile in the central region of the plasma. As, in turn, the q-profile is known to impact the global plasma confinement, this opens an additional promising application for ICRF as a control system in high-temperature D-T plasmas.
E. Complementary scenarios to demonstrate alpha particle effects in future D-T experiments on JET One of the main objectives of the forthcoming D-T campaign on JET (DTE2) is to demonstrate and study the effects associated with the presence of fusion-born alpha particles. 74,75 To achieve this task, JET is developing a dedicated scenario to excite alpha-driven AEs in the afterglow phase of high-performance D-T plasmas with internal transport barriers, heated with NBI-only. 76 The success with the development of three-ion ICRF scenarios in H-D and D-3 He plasmas on JET opens new promising routes for demonstrating alpha effects in JET-ILW. In particular, we note the ongoing effort for designing a dedicated scenario to demonstrate alpha particle heating in DTE2, in which fusion-born alphas provide the main source of electron heating in the plasma core and where the post-sawtooth reheat rate, dT e (0)/dt is used as a figure-of-merit to characterize electron heating power densities in the plasma core. 77 In this context, applying three-ion ICRF scenarios with heavier impurities as resonant absorbers ( 9 Be, possibly in combination with Argon or 22 Ne) is promising as they collisionally transfer most of the absorbed RF power to bulk ions and thus minimize core electron heating from ICRF. Equally important, these heavy resonant ions stay at sub-Alfv enic velocities and thus are less likely to trigger AEs even at MeVenergies.
In addition, three-ion ICRF scenarios with fast T-NBI or D-NBI ions as resonant absorbers are also promising for their use in DTE2. As we demonstrated the possibility to control the fast-ion distribution with the ratio P ICRF /P NBI and the choice of NBI injectors, this technique offers JET the possibility to accelerate NBI ions with ICRF to energies, for which the D-T reactivity is maximized, as proposed in Ref. 19. In this way, this technique can be used to optimize the alpha production and beam-target neutron rate in D-T plasmas at moderate input heating power. Similar to the D- 3 He experiments discussed in Sec. III A, rather high alpha generation rates can thus be obtained for a moderate total auxiliary heating power. In combination with the offaxis location of the IIH layer and beam heating, the energies of ICRFaccelerated fast ions can be controlled to be below or comparable to the critical energy. Thus, this scenario can facilitate the design of dedicated experiments to demonstrate alpha physics effects in JET-ILW.

F. Extending H-mode access in hydrogen majority plasmas in ITER
Access to ELMy H-mode plasmas and developing ELM control techniques are one of the main priorities for ITER studies with nonactive plasmas. 48 Partly due to the lack of an efficient ICRF absorption scenario in hydrogen plasmas at half magnetic field (2.65 T/7.5 MA), this may be challenging for such plasmas. For H-mode access, the difference in the total auxiliary heating power available, 53 MW (NBI þ ECRF) vs 73 MW (NBI þ ECRF þ ICRF), could well be essential. Thus, an alternative heating scenario with all three heating systems of ITER was proposed in Ref. 51. This relies on using the mix H þ 10%-15% of 4 He ions (shown to reduce the L-H power threshold in NBI-only heated plasmas in JET-ILW 78 ) and increasing the nominal magnetic field to 3.0-3.3 T. In these plasmas, the three-ion 4 He-( 3 He)-H ICRF scenario with an off-axis 3 He resonance [n( 3 He)/n e <1%] is capable to provide an additional 20 MW of heating power to the plasma. Thus, this heating scenario has the potential to extend the H-mode operational space in predominantly hydrogen plasmas in the PFPO-2 phase of ITER. 38,51 As discussed in Sec. III C, in view of ITER needs, promising results have been recently obtained on AUG and JET. Particularly relevant are the pioneering results with the off-axis three-ion 4 He-( 3 He)-H ICRF scenario in H-4 He plasmas on AUG, in which all three heating systems were used. The simultaneous realization of plasma heating with ICRF, ICRF-triggered L-H transitions, and low levels of impurities is encouraging. Further studies of this ITER- G. Using impurities as an active tool to control RF polarization and ICRF absorption

Physics of Plasmas
The role of low-Z impurities in multi-ion species plasmas can go beyond being an absorber of RF power, as for 9 Be and 7 Li ions in D-T plasmas. Low-Z impurities can also provide a significant contribution to the RF polarization, as, e.g., for the carbon impurities during 3 He ICRF experiments in hydrogen plasmas in JET with the carbon wall, 15,64,65 discussed in Sec. IV C. Yet nothing prevents extending this idea and using a combination of intrinsic and extrinsic impurities as an active tool to control polarization and deposition of RF waves.
Because of the unavoidable presence of 9 Be impurities in ITER and JET-ILW plasmas, neither pure ( 4 He)-H, nor (D)-H minority scenarios can be realized in these machines. Because (Z/A) 9Be < (Z/A) 4He < (Z/A) H , 9 Be impurities are not resonant absorbers in these plasmas, but are a crucial component that defines the polarization of RF waves and, thus, impacts RF heating of resonant 4 He ions. 17,79 This is illustrated in Fig. 20, where the fraction of RF power absorbed by resonant 4 He ions is plotted as a function of both n( 9 Be)/n e and n( 4 He)/n e , computed by the full-wave TORIC code. 35 It is very clear that power absorption by 4 He can vary from 0% to 100%, depending on the plasma composition. For example, if n( 9 Be)/n e >3%, then ICRF heating of 4 He ions becomes a very poor heating scenario with unwanted strong fast wave reflections. Figure 20 shows that efficient ICRF absorption by 4 He ions at very low concentrations ($0.2%) is maximized at n( 9 Be)/n e % 1.5%-2.5%, in line with the theoretical formulas for the three-ion 9 Be-( 4 He)-H scenario [Eq. (5)]. These conditions are beneficial if one aims to generate MeV-range 4 He ions in hydrogen majority plasmas, e.g., to validate fast-ion diagnostics.
As controlling the concentration of 9 Be intrinsic impurities (Z/A ¼ 4/9) in the plasma is not straightforward, using other extrinsic impurities with a similar charge-to-mass ratio can be applied as an additional control tool. These include argon (Z ¼ 18, A ¼ 40; ionization energy of the fully stripped ions E ioniz. % 4.4 keV) and 22 Ne (Z ¼ 10, A ¼ 22; E ioniz. % 1.4 keV), currently considered for impurity seeding in ITER and future reactors. 70 Accounting for such impurities, the equivalent concentration of 9 Be is given by X½ 9 Be equiv: ¼ X 9 Be ½ þ ð10=4ÞX 22 Ne ½ þ ð18=4ÞX Ar ½ : The numerical coefficients in Eq. (13) reflect the fact that 22 Ne and Ar ions have a higher charge number than 9 Be. For example, if the intrinsic level of 9 Be impurities is about 0.5%, then an additional impurity seeding with $0.1%-0.4% of argon would result in maximizing the RF power absorption on 4 He ions at concentrations nð 4 HeÞ=n e Շ 0:5%.

VI. SUMMARY AND CONCLUSIONS
ICRF heating of multi-ion species plasmas has been often employed in fusion research. Already in the 1980s, there were theoretical and experimental efforts on the T-10 and TFR tokamaks to use extrinsic impurities such as 22 Ne and Ar to improve the efficiency of ICRF heating and exploit the advantages of the enhanced E þ RF electric field at the IIH layer in mixed H-D plasmas. [80][81][82] However in those times, second harmonic ICRF heating of impurity ions, x % 2x ci (n ¼ 2) was selected as a damping mechanism, which is a finite-Larmor-radius effect.
In multi-ion species plasmas, ICRF heating could be made much more effective using fundamental (n ¼ 1) heating for a "third" ion population. Sporadic observations of RF power deposition on ions were reported in mixed D-T and D- 3 He plasmas under conditions where mode conversion was expected. For example, dominant RF power absorption on 7 Li impurities was reported in D-T experiments on TFTR, designed for electron heating via mode conversion. 21 Similarly, in ICRF mode conversion experiments in D-3 He plasmas, additionally heated with D-NBI, an unexpected generation of high-energy D ions was observed at large n( 3 He)/n e % 25%. 12 The developed theoretical framework for three-ion ICRF scenarios provides a simple and unified explanation for the direct RF absorption by the ions in these experiments, while mode conversion heating was expected. In retrospect, the idea behind these scenarios sounds self-evident. The essential RF physics mechanisms, in particular, the importance of the plasma composition and the presence of impurities in multi-ion species plasmas, the enhanced left-hand RF polarization at the IIH layer, Doppler-shift effects for fast ions, etc., were individually well known by the ICRF community for years and recognized in past ICRF experiments on TFTR, JET, and AUG.
The intentional use of three-ion ICRF scenarios only started a few years ago. Recent experimental and modeling developments of these scenarios on Alcator C-Mod, AUG, and JET tokamaks provided new insights for the exploration of these novel ICRF scenarios for many fields of fusion research, extending their applications beyond the originally intended fast-ion generation and plasma heating.  4 He ions in hydrogen majority plasmas, including 9 Be impurities. The computations were made for the ITER-like plasma conditions using the TORIC code (B 0 ¼ 5.3 T, f ¼ 40 MHz, n tor ¼ 27, n e0 ¼ 6 Â 10 19 m À3 , and T 0 ¼ 10 keV). An additional seeding of 22 Ne and Ar impurities can be applied to complement intrinsic levels of 9 Be to optimize the three-ion ICRF scenario for 4 He resonant ions.
As presented in Sec. V, three-ion ICRF scenarios hold promises for ITER to extend the H-mode operational space in its nonactive phase and to provide bulk ion heating of D-T plasmas using intrinsic 9 Be impurities (or in combination with impurities like Ar and 22 Ne, considered for impurity seeding). Furthermore, recent experimental results have shown further applications of these scenarios, including many also of relevance for ITER. These include a tool to study fast-ion driven MHD modes, turbulence studies at ITER-relevant fast-ion electron heating conditions, efficient generation of large populations of passing fast ions, local fast-ion current drive and modification of the q-profile, etc.
Three-ion scenarios open new possibilities for the application of ICRF in fusion research, and they also allow revisiting old and sometimes forgotten ideas. As an example, the well-known absorption of ICRF power by alpha particles in D-T plasmas, up until now considered as detrimental, in fact, now opens new potential applications for ICRF in high-temperature fusion-grade plasmas. There is an important and promising field in plasma physics to be further explored.

ACKNOWLEDGMENTS
The authors are grateful to the anonymous reviewers for their constructive comments that allowed us to improve the paper, I. Voitsekhovitch for her valuable comments and suggestions during the paper preparation, and to H. Meyer and J. Faustin for fruitful discussions. We thank the ITPA Energetic Particle Physics Topical Group for its support. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 and 2019-2020 under Grant Agreement No. 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission. Part of this work was also carried out in the framework of projects done for the ITER Scientist Fellow Network (ISFN).
ITER is the Nuclear Facility INB No. 174. The views and opinions expressed herein do not necessarily reflect those of the ITER Organization. This publication is provided for scientific purposes only. Its contents should not be considered as commitments from the ITER Organization as a nuclear operator in the frame of the licensing process.

DATA AVAILABILITY
The data that support the findings of this study are available from the corresponding author upon reasonable request.